Fermentation tanks
Bucket Semi-Transparent with Lid 5 litres
€5.95*
Semi-transparent bucket made from foodgrade HDPE. Lid Included.
Volume 5 litres
Complete with Handle
Lid with guarantee closure
Graduation
Natural Colour / semi transparent
Size: height 18,7 cm Ø 23,8 cm
Important: Bucket is without spigot.
Bottle filler for tap Large
€4.45*
Bottle full? This bottel filler stops automatically when you remove the beer bottle.Fits on the drain valve for barrels of 30-60 liter and Braumarkt brew bucketsLength: 40 cmFills the liquid along the bottom so minimal oxidationDoes not fit on the valves of Speidel Barrels!
Insulation Jacket for FB30 Fermenter
€30.95*
The Easybrew insulation jacket is a handy accessory for those cold winter days. It will help you to keep the temperature in your fermenter during colder days to prevent your fermentation from stalling.
Oxebar PET Keg 4L with Cap and Handle
€7.50*
The 4L Oxebar Plastic Keg is a compact, lightweight, and reusable container perfect for storing your homebrew. With its smaller size, it’s ideal for camping, BBQs, or sharing drinks with friends. The keg features an advanced Oxebar Mono PET polymer blend, which provides superior oxygen barrier properties, keeping your beverage fresh for up to 6 months.
This keg fits in most coolers and fridges and can even be dispensed while lying on its side. It comes with a PCO38 cap, but for draft dispensing, you can add the PCO38 Tapping Head (sold separately).
Key Features:
4L capacity
Superior oxygen barrier, preserves freshness
Suitable for carbonated and non-carbonated drinks
Diameter: 155mm, Height: 325mm
Max pressure: 4 Bar / 58psi or 45°C
Note: Periodic hydrotesting required every 2 years.
Brew Bucket Semi Transparent 12 Litres incl. Lid
€10.95*
Brewing bucket semi transparent for pulp and main fermentation complete with:
Lid
Size distribution
Handle
Tap
Airlock
Connection for the water seal by means of a 100% silicone plug
Especially suitable for foodstuffs.
Ideal for pulp and main fermentation.
Measurements: height 27.5 cm Ø 27.5 cm
Content 12 Litres.
Before use:
Mount the tap in the bucket with the white ring on the outside. Hold the white part on the outside of the tap and carefully tighten the nut on the inside. Over tightening causes leakage.
Place the bucket on the edge of the table and fill it with 5 Litres of water to test for leaks before use.
The temperature of the liquid in the brewing bucket most never exceed 65 ° C.
Prevent damage from scratching the plastic to prevent unwanted bacteria.
Brew buckets are ideally suited for the 1st or main fermentation because there is sufficient CO2 above the liquid.
Always use a fermentation vessel with rubber ring for 100% sealing, or a glass bottle with stopper and airlock.
Oxebar Monolayer Keg 8L With Cap and Handle
€10.95*
This compact and lightweight 8L reusable plastic keg is the perfect solution for storing homebrew in a smaller, more portable container than traditional 19L kegs. With its high oxygen barrier, it keeps beverages fresh 3 times longer, making it ideal for both carbonated and non-carbonated drinks.
Key Features:
Holds up to 8L of liquid
3x better gas barrier than standard PET plastic
Capable of storing beer or other oxygen-sensitive drinks for up to 6 months
Recommended maximum pressure: 4 Bar (58psi) or 45°C
Includes PCO38 cap; optional PCO38 Tapping Head (KL20169) for draft dispensing (sold separately)
Dimensions:
Diameter: 155mm
Height: 520mm
Hydrotesting:
Test every 2 years at 6 bar (simple instructions included).
Perfect for sharing drinks with friends, and easy to maintain.
Insulation Jacket for FB60 Fermenter
€38.95*
The Easybrew insulation jacket is a handy accessory for those cold winter days. It will help you to keep the temperature in your fermenter during colder days to prevent your fermentation from stalling.
Easybrew Chillercoil for 30L bucket
€76.45*
The Easybrew Chillercoil is one of those tools that can help you brew better beers.
The Chillercoil allows you to control the fermentation temperature of your wort.
Specifications:
Material: 304 stainless steel
Coil Length: 4.7m.
Hole for airlock.
Spunding Valve with Pressure Gauge 1.5" Tri Clamp
€167.95*
High-quality stainless steel Spunding valve with integrated pressure gauge. The spunding valve is fitted with Tri-clamp couplings which makes cleaning and fitting a breeze. Easily adjustable and fully demountable.
Specifications:
Material: stainless steel 304
1.5" TC coupling.
Adjustable from 0.2-2.2 Bar.
Easy to clean.
Note: Use Spunding valve only on suitable pressure tanks.
Apollo 30l Unitank Pressure Fermenter
€184.95*
The Apollo 30 L Unitank Pressure Fermenter takes brewing to new heights. This is the perfect fermenter to get into pressure fermentation, allowing you to ferment and carbonate in one vessel, meaning you get to drink your beer sooner.
With its conical shape, and clear, high-strength PET build, the Apollo allows you to ferment quality beer, under pressure, with confidence.
Specifications:
Stainless steel plunge valve and collection bottle for dumping trub and harvesting yeast
A dry hop port for sanitary dry hopping
Multi pressure option PRV selection - select the pressure setting from the 3 x PRVs included
Centralised floating dip tube for clear transfers
Thermowell to monitor the internal temperature
Built in handles
True conical shape
Stainless steel stand
When finished, the beer can be served directly from the fermenter, or transferred to a keg without introducing oxygen. Each unit is pressure tested straight off the production line.
FermZilla - Tri-Conical - 27L - Starter Kit with handle (Gen 3)
€147.95*
The Gen3 FermZilla 27L Tri-Conical is an advanced fermentation vessel perfect for homebrewers and small breweries. Featuring a 3-inch Tri-Clover ferrule, a 600mL collection container, and an easy-to-clean design, it offers a simple, sanitary solution for fermenting under pressure (up to 2.4 bar). This new model is designed for ease of use and maintenance, with a clear view of the fermentation process.
Key Features:
3-inch Tri-Clover ferrule and butterfly valve for easy cleaning
600mL collection container with Tri-Clover connection
Ferments under pressure up to 2.4 bar
Transparent design for monitoring fermentation
Starter Kit Includes:
27L Tri-Conical tank with metal neck ring
Standard top lid with PRV (35psi)
600mL collection container & lid, Tri-Clover clamps, and more
The Gen3 FermZilla is easier to clean, disassemble, and is ideal for brewers at all levels.
Dimensions:Height - 750 mm Height with airlock - 856 mm Width - 388 mm Circumference - 352 mm
Apollo 30l Snub Nose
€152.45*
The Apollo 30 L Snub Nose Pressure Fermenter takes brewing to new heights. This is the perfect fermenter to get into pressure fermentation, allowing you to ferment and carbonate in one vessel, meaning you get to drink your beer sooner.
With its conical shape, and clear, high-strength PET build, the Apollo allows you to ferment quality beer, under pressure, with confidence.
Specifications:
A dry hop port for sanitary dry hopping
Multi pressure option PRV selection - select the pressure setting from the 3 x PRVs included
Centralised floating dip tube for clear transfers
Thermowell to monitor the internal temperature
Built in handles
True conical shape
Stainless steel stand
When finished, the beer can be served directly from the fermenter, or transferred to a keg without introducing oxygen. Each unit is pressure tested straight off the production line.
Speidel 3/4" Stainless Steel Ball Valve for FD Tanks
€86.45*
Speidel 3/4 "stainless steel ball valve for FD tanks.
Male connector - Female connector 3/4 ", V2
Brewing Bucket Semi-Transparent Complete - 25 litres
€11.95*
'Semi-transparent bucket made from foodgrade HDPE. Contains of a lid (with pre-drilled hole), volume indicator, handle, spigot, airlock and silicone plug for airlock.
Perfect as fermenter or bottling bucket.
Volume: 25 litresWidth with lid : 38cm
Height with lid : 36cm
Diameter : 38 cm
Important: Mount the rubber ring of the spigot on the outside of the bucket. Tighten the nut on the inside carefully. Overtightening can cause leakage!
Speidel 1" Stainless Steel Ball Valve for Ferment-Egg
€87.45*
Speidel 1"stainless steel ball valve for Ferment EggMale connector - Female connector 1 ", V2
For the FermentEgg 2 spigots are necessary.
Grainfather conical fermenter cooling pump kit
€87.45*
Temperature control is one of the most crucial elements for producing a beer of good quality. It must be regulated throughout the fermentation process and be stable to ensure that the yeast does not get stressed and ferment in the right way to get the right flavor profile.
To cool off with the Grainfather Conical Fermenter, you must have the Conical Fermenter Temperature Controller. As soon as your target temperature is lower than the temperature of the wort in your digester, the cooling pump set pumps ice-cold water through the double-walled, insulated interior to cool your wort.
Simply connect the couplings and insulated hoses to the Conical Fermenter, immerse the submersible pump in a cool box with water (add ice for the desired temperature) and pump the liquid through the insulated cooling of the Conical Fermenter housing.
FastFerment™ stand extension kit
€40.95*
These Leg Extensions allow you to extend the Stand for the 14G FastFerment™. This way a Keg can be fitted under the FastFerment™ for easy filling.50,8 cm in length12 mm Diameter Legs and 14 mm diameter RingWorks for 14G (53L) versionsHeight from Ground to Airlock - 156.7 cm Height from Ground to Top of Lid - 147.8 cmTotal Clearance from Valve to Ground for Kegging 66 cm
FermZilla - Tri-Conical - 55L - Starter Kit with handle Gen3
€169.95*
The Gen3 FermZilla Tri-Conical is a game-changer for homebrewers, featuring a 3-inch Tri-Clover ferrule, a 600mL collection container, and easy-to-use Tri-Clover connections. Designed based on customer feedback, it offers simpler, more sanitary design and effortless disassembly.Key Features:3-inch Tri-Clover ferrule and butterfly valve for easy cleaning600mL collection container with Tri-Clover connectionFerment under pressure up to 2.4 barTransparent design to monitor fermentationStarter Kit Includes:55L Tri-Conical tank with metal neck ring Standard top lid with PRV (35psi) and accessory ports 600mL collection container & lid, Tri-Clover clamps, and more The new Gen3 model is easier to clean and assemble than its predecessor, making it perfect for brewers at all levels.Dimensions:Height - 1055 mmHeight with airlock - 1146 mm Width - 388 mmCircumference - 354 mm
Speidel Plastic Fermenter 20 litres with Spigot and Airlock
€46.45*
Plastic fermenter made from high quality white foodgrade HDPE (High Density Polyethylene) which is acid and alcohol resistant. Has a large top opening for easy cleaning and comes with spigot, rubber stopper and cylindrical airlock.
Capacity: 20 litres
Size: Diameter 310mm, Height 418mm
Jacket for Apollo 60l Unitank
€100.95*
This Jacket from Keg King fits the Apollo 60L Unitank. The Jacket will help control the temprature when fermenting. Especially helpfull when doing tempreture controlled fermentation.
Oxebar Monolayer Keg 8L incl. Tapping hat kit
€23.95*
Oxebar 8L Keg Bundle – Monolayer Keg with Cap & Handle + Tapping Head Kit
This convenient bundle includes everything you need for your kegging setup:
Oxebar 8L Monolayer Keg with a sturdy cap and handle for easy transport
Tapping Head Kit designed for Oxebar kegs (PCO38) for easy dispensing
Perfect for homebrewers, this kit makes kegging simple, efficient, and ready to use.
Oxebar PET Keg 4L incl. Tapping hat kit
€19.95*
Oxebar 4L PET Keg Bundle – Keg with Cap & Handle + Tapping Head Kit (PCO38)
This convenient bundle includes everything you need for your smaller keg system:
Oxebar 4L PET Keg with cap and handle for easy transport
Tapping Head Kit designed specifically for Oxebar Kegs (PCO38) for quick and easy tapping
Perfect for smaller batches – everything you need to get started with kegging!
Apollo 60 l Unitank Pressure Fermenter kit
€227.95*
The Apollo 60 L Unitank Pressure Fermenter is big enough to match your homebrewing ambitions! Pressure ferment and carbonate a double batch of quality craft beer in one 60 L tank.
With its conical shape, clear, high-strength PET build, and high level of fermentation control, the Apollo allows you to ferment under pressure, with confidence.
Product Specifications:
Stainless steel plunge valve and collection bottle for dumping trub and harvesting yeast
A dry hop port for sanitary dry hopping
Centralised floating dip tube for clear transfers
Thermowell to monitor the internal temperature
Built in handles
CIP Capability
True conical shape
Stainless steel stand with castors
When finished, the beer can be served directly from the fermenter, or transferred to a keg without introducing oxygen. Each unit is pressure tested straight off the production line.The Spundy from Keg King is a neat little gadget that works as well as any spunding valve on the market. With a low profile - just 4.5 cm tall - the Spundy doesn't take up much room in fermentation chambers or kegerators.
FermZilla - All Rounder 30L -Starter Kit
€69.95*
The KegLand FermZilla 30L All Rounder is a versatile fermentation vessel designed for fermenting under pressure, carbonating, and dispensing. For pressure use, we recommend the pressure kit. Key Features: Ideal for fermentation, carbonation, and dispensing Pressure-capable with the recommended kit Durable PET construction designed to withstand minor dents and high pressure Important Notes: Always read instructions and perform a water pressure check for leaks. Keep out of direct sunlight to avoid PET degradation. Minor dents from shipping are normal and won’t affect performance. This kit includes:1 x All rounder tank 30L1 x Stainless Steel Handle Assembly1 x 304 stainless stand1 x Airlock1 x Pressure rated lid1 x Digital temperature sticker1 x Red 2.5bar pressure relief valve1 x Graduation StickerDimensions: Height - 552 mm Height with airlock - 614 mm Circumference - 352 mm